 |
| |
| Tugger Lift Straps |
 The Tugger Lift Strap provides a
convenient gripping point near the front or rear of your dirt bike.
Most dirt bikes don't have a place to grab that won't toast your
fingers or get your gloves all muddy.
The Tugger lift strap is ready when you need it and stays
out of the way when you don't. Perfect on the trail when you need to
maneuver your bike over a rock, around a tight switchback or get it
out of a deep rut. No more burning your hand on your hot silencer,
getting your gloves covered in mud from grabbing the rear fender or
breaking the fenders because you used them as a handle.
a
Easy to install, lightweight, tough, and convenient. Fits nearly any
motorcycle that uses two bolts to attach the seat to the subframe
(16" max length between the bolts).
The front Tugger lift strap mounts to the front forks, providing
a handy place to grab when you get in those situations where someone else is
pulling on your bike. And for you adults riding with your child, the front
Tugger is especially handy for helping your child through nasty situations. |
|
Rear Tugger Style 5
|
Rear Tugger Style 5 - Mounts to the subframe of some of the new Husqvarna models. Easy to install, lightweight yet rugged. Weight: 1.1 oz, includes mounting hardware. |
 |
 |
 |
| |
Rear Tugger Style 1
|
|
The Style 1 Extreme Enduro rear Tugger has stainless steel buckles on the webbing assembly and should last forever. Easy to install, lightweight, tough, and convenient with typical mounting hardware. Weight: 1.8 oz.
Fits nearly any motorcycle that uses two bolts to attach the seat to the subframe (23 max length between the bolts).
BEFORE ORDERING: Review the Application Chart |
 |
| Style 1 Rear Tugger Extreme Enduro |
Style 1 - 2009 KTM mount |
 |
 |
| Style 1 - KTM with sub fender mount |
Style 1 - Most bikes mounts like this |
 |
 |
|
| |
Rear Tugger Style 3-4
|
|
The Tugger™ Style 3-4 has multiple high-strength grommets, allowing you to install it using various bolt locations on many different motorcycles.
Easy to install, lightweight yet rugged. Weight: 1.5 oz. Backed by Tugger no-nonsense lifetime warranty.
BEFORE ORDERING: Review the Application Chart |
 |
 |
|
| |
Front Tugger Style 6 Triple Clamp
|
Style 6 Triple Clamp Tugger - Built at the request of snow bikers, the Style 6 Triple Clamp Tugger mounts to the top triple clamp and extends vertically above the handlebar to provide a convenient location to grap your snow bike
even when buried in the white stuff. Constructed using two layers of Tugger webbing with an internal stiffener to handle the worst abuse. Easy to install, lightweight, tough, and convenient. Backed
by our no-nonsense After riding with the Tugger, you'll never want to ride without one again. Weight: 3 oz!
INSTRUCTIONS:
1. Remove one top triple clamp bolt. Use the top bolt for max height, the lower one if you want the Tugger dirt bike strap a little lower.
2. Decide if the stock bolt can be used; if not, use one of the bolts included in your Tugger kit. You may need to cut the bolt a little shorter for some models.
3. Slide the Tugger metal end piece over the aluminum bushing, insert the bolt and tighten.
4. Route the Tugger dirt bike strap as desired and repeat on the other side.
|
 |
 |
|
| |
Front Tugger Style 2 Extreme Design
|
|
Style 2 Front Tugger Extreme Enduro - An upgrade from the standard Style 2 front Tugger dirt bike strap, the Extreme Enduro version is thicker where you grab and has a non-slip covering to handle the worst abuse. It
retains the simple and effective buckle attachment system that allows installation on any forks without tools. Because of the extra thickness, custom embroidery is not available. Like the original Style
2, the Style 2 Tugger Extreme Enduro mounts to the front forks, providing a handy place to grab when you get in those situations where someone else is pulling on your bike. You hard-core enduro riders will love it!
And let's face it: we all get into nasty situations occasionally - that's part of the fun! Watch this video and you'll see what we mean:
Extreme Enduro video The tire is slippery and muddy and will cause a loop-out if you're on a hill because you're lifting as well as pulling. The
fender is also too slippery and muddy, and most handlebars don't have a crossbar to grab. The Style 2 Tugger comes in handy in the nastiest of situations or even just loading your machine into
the truck. The front Tugger is made from the finest materials available. Like the rest of the Tuggerline, it is built to work well, look good, and last. Installed weight: 2.2 oz! |
| |
| Style 2 Front Tugger Extreme Enduro |
 |
|
| |
Front Tugger Style 2 - Original Design Upgraded
|
|
The Front Tugger Style 2 mounts to the front forks, providing a handy place to grab when you get in those situations where someone else is pulling on your bike. You hard-core enduro riders will love it!
The Style 2 Tugger™ comes in handy in the nastiest of situations or even just loading your machine into the truck. |
 |
|
 |
|
 |
|
